Site Overlay

MANUAL CADDX NX4 PDF

The NXZA-TK (from now on called NX-4) NetworX from Caddx represents a new approach to the design of security systems. The NX-4 is probably the most. The NetworX NX-4 from CADDX Controls represents a new approach to security systems design. Drawing on our experience in the world market as the largest. Click the photo of your keypad or choose from the list below. CADDX Manuals. CADDX NX E User Manual (PDF, MB) ยท CADDX NX E User Manual.

Author: Mujinn Akiran
Country: Monaco
Language: English (Spanish)
Genre: Education
Published (Last): 26 August 2012
Pages: 68
PDF File Size: 10.27 Mb
ePub File Size: 15.43 Mb
ISBN: 823-4-18309-170-9
Downloads: 36079
Price: Free* [*Free Regsitration Required]
Uploader: Dougor

We understand More information. If immediate restore is not enabled, a second or subsequent alarm will not be sent until the siren times out.

The alarm report will also be sent. You definitely have an expansion board of some manuap. For example, your zone 3 totals 6 which is an instant zone. As before, you are now ready to enter another programming location. The board locations in programming are manuall specific list. Before ringing ADT i decided just to do a little more searching on the net for info on the nx-4, and came across some system called a “DAS NX-4” hosting from an australian site, so i looked up the installer manual for the das nx-4 and it seemed almost identical to the caddx installer manual, however the locations called features in this manual were different numbers!

Is there a flashing. What do cadxx set your thermostat at? Please assign your manual to a product: Auxiliary will activate the steady Fire siren, Auxiliary will sound the keypad, and the Keypad Panic can be programmed to be silent or audible sound siren.

  BLACKMAGIC DESIGN VIDEOHUB MASTER CONTROL PDF

The defaults for both delay1 and delay2 are 30sec entry and 60 second exit. Turn the LED on for the features that you desire.

For locations with a maximum of, the hexidecimal equivalent will be displayed in parenthesis. If the report is not aborted within the allotted time, the LED will extinguish when the report is sent. Enable Ding Dong sound for Chime – If off, chime cadfx be a single tone. Find all posts by azhar. To exit at any time during this mode, enter a user code. I went to the correct feature zone editing, 18 and all the segments matched up, i was able to set the zones to type 3, tested it all cardx and it works perfectly So i would have to assume the “DAS” nx-4 systems are perhaps just modified caddx systems for the australian market?

If dual or split reporting is not desired, location should be left at the factory default of “0”. The following features can be enabled or disabled using this location. All codes must have the same number of digits. Newsletter Sign-Up Signup Email address. This can give dark shots. OK I am with you so far. If there is a system trouble, pressing [r]-[] will still show the service menu. The mznual of the faulted zone s will be displayed on the LCD keypad. Rinse light flashing rapidly and cycle stoped.

To exit before the last segment, press [ ]. Enter [hour cadxd digit]. Thanks for your help MrRon, I am in australia, would this change the installer code? Otherwise, the AWalk-Test will automatically exit after minutes. I armed this alarm system with the default code but could not disarm it. If no events should be reported to Phonelocation caaddx be programmed as “0” disabled.

  GOSPODJICA IVO ANDRIC PDF

While using the scroll keys you can change any digit by caddz a new digit. Select a format from the list on the following page. Understanding the Code Pad lights See Feature Definitions starting on page Segment: The arming process will be stopped if a code is entered on ccaddx keypad.

SOLVED: Hi, i’m using the Caddx NX4V2, the fire light – Fixya

If this location contains a “0”, format will be used when Phone caddx dialed. This is not recommended for commercial applications. Even with add-ons a NX-4 maxes out at 8 zones.

If enabled, when the next report is successfully communicated, a Fail to Communicate code will be reported. Refer also to the programming worksheets.

I will give it a try tonight when I get home.

Need help adding a entry/exit delay to zone

Use the following procedures when working with these two data types: Press [ ] to save and exit. To program the NX- Control Panel, enter [0]- [ ]. Can you explain in future detail, in the event I need to reprogram another zone?