Site Overlay

IC HT12D PDF

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.

Author: Gukazahn Minris
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Business
Published (Last): 13 November 2010
Pages: 80
PDF File Size: 17.98 Mb
ePub File Size: 17.81 Mb
ISBN: 177-3-39149-934-3
Downloads: 40478
Price: Free* [*Free Regsitration Required]
Uploader: Mugis

What is Web Browser. This high-density System-in-Package SiP integrates controller, power switches, and support components. In simple terms, HT12D converts the serial input into parallel outputs.

How IC HT12D works? | JAY Robotics’s Blog

Connected to the Ground of circuit. TL — Programmable Reference Voltage. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received.

If you want security you can connect any of the 8 pins to 5V to make it high. Interface GPS with Arduino. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

HT12D Decoder IC

The data on 4 bit latch type output pins remain unchanged until new is received. The IC has a built in oscillator. It is not mandatory to use it. These are the 8-bit address bits, which is used to protect your data. Skip to main content.

  EDAD GESTACIONAL POR FUM PDF

The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. The serial input data is compared with the local addresses three times continuously.

The Encoded 12 bit output data obtained from HT12E has to be given here. Valid transmission; active high.

Virgin Galactic — Commercial Space Flight. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

HT12D Decoder IC | HT12D Datasheet | Pin Diagram

They can also be connected to LED to physically view the received data. We should set the bits in same pattern on Encoder and Decoder IC to pair them.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. If any valid data is received they can be obtained from these four pins. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Interface SD Card with Arduino. It is very important that your Decoder should have the same address of that of the encoder.

How IC HT12D works?

Submitted by admin on 27 October Supply voltage; 5V 2. This pin powers the IC should use only 5V.

This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc.

  GORDON LIGHTFOOT SONGBOOK PDF

So if you are working ut12d a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. Choosing Motor For Robots. These ci ICs together form an Encoder and Decoder pair.

The input data code is decoded when no error or unmatched codes are found. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Uc valid transmission in indicated by a high signal at VT pin. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

This pin will go high when a data is received. They are paired with 2 12 series of encoders.

It is mainly provided to interface RF and infrared circuits. Arduino based GPS receiver. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. SPI Module of Arduino. This oscillator can be used by connecting these two pins through a 1M Resistor.