Site Overlay

IC HT12D PDF

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.

Author: Nemi Zolozragore
Country: Greece
Language: English (Spanish)
Genre: Music
Published (Last): 24 April 2012
Pages: 92
PDF File Size: 7.24 Mb
ePub File Size: 18.39 Mb
ISBN: 441-7-66132-270-6
Downloads: 62157
Price: Free* [*Free Regsitration Required]
Uploader: Dougrel

Interface GPS with Arduino. Choosing Battery for Robots. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

They are paired with 2 12 series of encoders. Virgin Galactic — Commercial Space Flight. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Skip to main content. We should set the bits in same pattern on Encoder and Decoder IC yt12d pair them. Arduino based GPS receiver. These two ICs together form an Encoder and Decoder pair. It is very important that your Decoder should have the same address of that of the encoder.

HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet

The serial input data is compared with the local addresses three times continuously. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Supply voltage; 5V 2. This high-density System-in-Package SiP integrates controller, power switches, and support components.

  KRAUTHEIMER TRE CAPITALI CRISTIANE PDF

This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. ci

The input data h1t2d is decoded when no error or unmatched codes are found. If you want security you can connect any of the 8 pins to 5V to make it high.

This oscillator can be used by connecting these two pins through a 1M Resistor. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins.

How IC HT12D works?

They can also be connected to LED to physically view the received data. TL — Programmable Reference Voltage.

These are the 8-bit address bits, which is used to protect your data. Interface SD Card with Arduino. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

This pin powers the IC should use only 5V. What is Web Browser.

How IC HT12D works? | JAY Robotics’s Blog

If any valid data is received they can be obtained from these four pins. This pin will go high when a data is received. Can be used in Home automation for short range ht12c switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

  DE DIVINA PROPORCIN LUCA PACIOLI PDF

The data on 4 bit latch type output pins remain unchanged until new is received. SPI Module of Arduino. Submitted by admin on 27 October It is mainly provided to interface RF and infrared circuits.

The IC has a built in oscillator. In simple terms, HT12D converts the serial input into parallel outputs. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Choosing Motor For Robots. Connected to the Ground h1t2d circuit. Valid transmission; active high. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

A valid transmission in indicated by a high signal at VT pin. It is not mandatory to use it.

The Encoded 12 bit output data obtained from HT12E has to be given here. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc.

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.