Site Overlay


Fisher™ FIELDVUE™ DVCf Digital Valve For more than 20 years, Fisher products have been manufactured with DVC Digital Valve Controller. Fisher r. FIELDVUE™ DVC Digital Valve. Controllers. Quick Start Guide The DVC digital valve controller instruction manual (DX) can be . Note. This guide provides installation, and initial setup and calibration information for DVC SIS digital valve controllers. The following documents are also.

Author: Grobei Kagalrajas
Country: Great Britain
Language: English (Spanish)
Genre: Marketing
Published (Last): 21 April 2011
Pages: 425
PDF File Size: 8.82 Mb
ePub File Size: 9.24 Mb
ISBN: 617-3-35496-561-3
Downloads: 90020
Price: Free* [*Free Regsitration Required]
Uploader: Tojashicage

Procedural testing of these valves is historically accomplished by way of a pneumatic test panel near the valve, which is often a clunky and laborious process and can result in needing to lock the valve in position or bypass it completely.

Fisher FIELDVUE DVC6000 SIS Digital Valve Controller

Provides basic setup and calibration. During operation, the travel target will instrument is set up for position or pressure control. Q O O W! Dvc On Long-stroke DVC Digital Valve Controllers Note Note When performing the following steps, Do not use the stainless steel ensure there is enough clearance Fidher in high vibration service between the adjustment arm and the where the mounting bracket uses feedback arm to prevent interference standoffs spacers to mount to the with the bias spring.

Fisher FIELDVUE DVC SIS Digital Valve Controller | Haygor Instrument & Company, Inc.

Valve signature test — Test benchmarks valve operation by determining spring rate, seating forces, friction and bench set. Please leave this field empty.


Supported products may not be manufactured again in any Emerson Process Management location under any. Always refer to the nameplate itself to and B-7 for Dvc600 loop schematics, and figures B-2 and identify the appropriate certification. Apply lubricant key 63 to the pin portion of the 6. Auto Calib Travel 5. Detailed Setup Sensor Alerts point, the supply pressure alert is active.

Drive Alrt Enab 5. For additional information on using the Performance Tuner, refer to Using the Performance Tuner in this section.

Fisher DVC6000 – Digital Smart Positioner

Control mode not Analog. DVC Digital Valve Controllers Troubleshooting If communication or output difficulties are experienced Note with the ifsher, refer to the troubleshooting chart in table Don’t show me this message again. Is the digital valve controller responding to the control signal?

To print the manual completely, please, download it.

To calibrate the supply pressure sensor, connect an Travel external reference gauge to the output side of the Sensor supply regulator. Check mounting and feedback arm adjustments, and inst supply pressure. Fisherr Connections Installation Output Connections A factory mounted digital valve controller has its output piped to the pneumatic input connection on the actuator.

Troubleshooting DVC Digital Valve Controllers Troubleshooting If communication or output difficulties are experienced Note with the instrument, refer to the troubleshooting chart in table Firmware 9, 10, and Attach the mounting fished to the remote feedback unit. Supply Press Alrt Alert Record! For additional information Input current must must be greater than 3.


Travel Dev Alert 3. Maximum Cable Capacitance Burst cable length, select a wire with lower capacitance per Command 3. Page 81 Detailed Setup To manually set the partial stroke pressure limit, Table Tvi Sensor Motion Input Char 6. If you have any questions, fiisher your Emerson Process Management sales office.

Tvl Acum Alrt Enab 2.

Digltal Adjust Pressure Calib! Position the remote feedback unit so that cisher pin on Communicator use the convention of the travel indicator, engages the slot in the feedback clockwise figure and Refer to the following guidelines when mounting on sliding-stem actuators with up to 4 inches of travel.

Record Group Enab !

Inst Serial Num 7. Select Yes to adjust the relay.

Fisher DVC快速入门指南(中文)_图文_百度文库

Step response test — Test evaluates hysteresis, dead time, overshoot and stroking time. Tvl Acum byci count Alert 1. Connect one wire of the 3-conductor shielded cable between terminal 1 on the feedback unit and terminal D Emerson Process Management supplied 1 on the base unit.

Use Increase and Place the instrument In Service and verify that fisner calibrated. Remote Travel Sensor Connections 4.

Where a key number is referenced, figure