Site Overlay

DATASHEET 2N2219 PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Tujas Tygogami
Country: New Zealand
Language: English (Spanish)
Genre: Relationship
Published (Last): 24 February 2015
Pages: 177
PDF File Size: 15.87 Mb
ePub File Size: 16.2 Mb
ISBN: 745-6-19299-319-8
Downloads: 98640
Price: Free* [*Free Regsitration Required]
Uploader: Kajishura

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Where h FE, is dafasheet current gain of the transistor which in our case is So to calculate the resistor value of the base we can use the formulae.

Complete Technical Details can be found at the datasheet given at the end of this page. TL — Programmable Reference Voltage.

2N Transistor Pinout, Specs, Equivalent & Datasheet

Amplifier modules like Audio amplifiers, signal Amplifier etc. To make 22n219 current flow through the transistor the value of base current I B can be calculated using the below formula:.

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. The value of this current can be calculated by the required amount of current that will be consumed by the load.

  KENNETH GOLDSMITH FIDGET PDF

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Current Drains out through emitter, normally connected to ground. In our 2n221 for a collector current of mA we have to pass a base current of daatasheet.

2N2219 Datasheet, Equivalent, Cross Reference Search

Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. So the value if R B will be. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

22n2219 So if you looking for an Datasneet transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

The 2N is a NPN transistor and is normally used as a switch in many circuits. But this calculation will lead to the closest value to start with. This stage is called Saturation Region. Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

  DIRECT2D TUTORIAL PDF

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

2N Datasheet(PDF) – NXP Semiconductors

Current flows in through collector, normally connected to load. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle. Another important thing to keep in mind, while using a transistor as switch is the base resistor.

This resistor is connected to the base pin of the transistor to limit the current flowing through the base. Here lets us assume the load here consumes around mA maximum so our collector current I C mA. Submitted by admin on 21 June As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor datashewt turn it on.