Site Overlay

ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Mikajinn Faekus
Country: Tanzania
Language: English (Spanish)
Genre: Marketing
Published (Last): 16 September 2004
Pages: 286
PDF File Size: 6.46 Mb
ePub File Size: 10.10 Mb
ISBN: 190-1-42121-159-1
Downloads: 74600
Price: Free* [*Free Regsitration Required]
Uploader: Meztizil

ASTM A, AM_百度文库

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Finish and Edges The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Notwithstanding the a6682 of a signature, the organization submitting the document asgm responsible for the content of the document.

A number in parentheses indicates the year of last reapproval.

Limits on such elements are by agreement between purchaser and supplier. C When the chromium is speci?

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Within the text, the SI units are shown in brackets.

Revision to Table 2. Conformance to SI tolerances is mandatory when the “M” specification is used. When the maximum manganese limit exceeds 1. C When edge, width and thickness are not de?

When the amount of vanadium, columbium, or titanium is less than 0. Within the text, the SI units are shown in brackets. Combining values from the two systems will result in nonconformance with the speci? The strip may be subjected to product axtm by the purchaser either for the purpose of verifying that the chemical composition is within speci?

  CISCO CATALYST 6509 E DATASHEET PDF

ASTM A682 Grade 1074

This standard has been approved for use by agencies of the Department of Defense. Table 3 shows requirements for additional elements.

Notwithstanding the absence of a zstm, the organization submitting the EDI transmission is responsible for the context of the report. A portion of the coil may be discarded prior to cutting the samples for retest. NOTE 2—Camber tolerances as shown in the table are for any mm length. However, under SI the preferred term in mass.

Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.

The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded astn rationalized values.

NOTE 1—Camber is a862 greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge.

For strip length under 8 ft. Current edition approved March 10, Normal coiling or piling does not provide a 3 Where an ellipsis. Number of Tests and Retests This edge is aztm when the width tolerance and edge condition are not as exacting as for No.

  CANON F-715S PDF

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

General Requirements for Delivery 4. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis.

The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis.

Over 12 Width Tolerance, W682 and Minus, in. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? However, unless the order specifies the applicable “M” specification aa682 SI unitsthe material shall be furnished to inch-pound units. Stay on Page Continue to Compass. Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi?

However, unless the order speci? B The sum of copper, nickel, chromium, and molybdenum shall not exceed awtm. The ability of manufacturers to meet the maximum xstm weights depends upon individual mill equipment.

A superscript epsilon e indicates an editorial change since the last revision or reapproval.