Site Overlay


L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Grojin Vubar
Country: Honduras
Language: English (Spanish)
Genre: Finance
Published (Last): 14 November 2013
Pages: 272
PDF File Size: 7.25 Mb
ePub File Size: 14.46 Mb
ISBN: 892-7-72970-665-2
Downloads: 9399
Price: Free* [*Free Regsitration Required]
Uploader: Nikojas

Historical Version s – view previous versions of standard. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

Only annealed conditions of grades speci? It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Last previous edition approved in as A — Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined.

Only annealed conditions of grades specifically asgm by the ASME code are permitted for pressure vessel use. C Annealed material that naturally meets mechanical properties may be applied. The values given in parentheses are for information only. This revision of Speci? The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test.

A — 03 Standard Speci? B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? Referenced Documents purchase separately The documents listed a6666 are referenced within the subject standard but are not provided as part of the standard.


Rockwell B 95 95 The steels shall adhere to specified chemical composition requirements. Link to Active This link will always route to the current Active version of the standard. Material Test Report and Certi?

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

This standard has been approved for use by agencies of the Department of Defense. The noncontrolling factor normally will exceed considerably the speci? The choice of test method for materials in conditions other than annealed shall be at the option of the seller. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

The values obtained in this manner should not, however, be taken as the actual yield strength for 0. ICS Number Code B Maximum unless otherwise indicated. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

This abstract is a brief summary of the referenced standard.

They shall be formed in different shapes such as sheets, strips, plates and flat bars. Number of Tests 8.


A superscript epsilon e indicates an editorial change since the last revision or reapproval. D PSS means plate, strip, sheet.

ASTM A Standard Specification for Annealed or Cold-Worked[1]_百度文库

In case of dispute, the offset method of determining yield strength shall be used. An alternative method of determining? Hard Elongation in 2 in. HardC Elongation in 2 in.

Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Originally approved in If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions.

The values given in parentheses are for information only. Current edition approved Oct. One bend test shall be made from one end of each coil. A number in parentheses indicates the year of last reapproval. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.