racy documents correlate as shown in Figure 1. Current Status of New Standards. In late , the new tangential accuracy stan- dard ANSI/AGMA A AGMA A01 (R). Accuracy Classification System – Tangential Measurements for Cylindrical Gears. standard by American Gear. CONTAINS ANSI/AGMA A ACCURACY CLASSIFICATION SYSTEM- TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS AND AGMA.
|Published (Last):||14 June 2017|
|PDF File Size:||9.35 Mb|
|ePub File Size:||2.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is developed by subtracting the ordinates of a straight–line gradient from the ordinates of the design profile. Tolerances for total cumulative pitch deviation are provided by the formula in 7.
An example of free input of helix shape on the Wenzel GearTec inspection machine is shown in Figure 4 and Figure 5. The 20151-a01 and orientation of the tolerance diameter circle are determined by the datum axis. This standard specifies tolerancing direction of measurement for single pitch deviation to be along the arc of the tolerance diameter, dT, circle within the transverse plane. Several types of filtering may be implemented in the gear measuring system.
Applications requiring high accuracy gearing may necessitate the matching, agna modifying, of pinion and gear profiles and helix such that the matched set is satisfactory for the 2015-1-a1.
Methods of measuring some of these characteristics agmx discussed in AGMA A02, and in the annexes. In general, these tolerances cover the following ranges: Master gears of accuracy grade 2 are recommended for verifying gear testers and checking production gears primarily of grades 4 and 5. The new AGMA gear inspection is a pure metric standard—Only a few notes are included regarding the inch system.
A New Standard in Gear Inspection | Gear Solutions Magazine Your Resource to the Gear Industry
When applications require measurements beyond those recommended in this standard, special measurement methods must be negotiated prior to manufacturing the gear. It provides an indication of compatible tooth shape, both up and down the tooth profile, and lengthwise on the tooth. High frequency test data that is near but not exactly at the cutoff is filtered proportionally according to its proximity to the cutoff wavelength.
Usually, a specific master is required for each different production gear design. Your Alert Profile lists the documents that will be monitored. Based on committee experience, the single flank tolerances shown in this standard are more appropriate for functional considerations.
Distinction is not made as agm the direction or algebraic sign of this reading. Single flank composite, total fis: Substantial agreement means much more than a simple majority, but not necessarily unanimity. Additionally, the formulas stated the tolerances in metric terms. In this standard the tolerancing direction varies with the given toleranced elemental parameter.
A judgement of compatibility may be made by the position and size of the contact area. Log in to leave a comment. 215-1-a01 master gear is a gear of known accuracy, designed specifically to mesh with the gear to be inspected for composite variation. Continuous Cooling Transformation Diagrams. Measurement and control of short duration roughness is beyond aggma scope of this standard. The inspection of gearing mated in an assembly for a specific application is beyond the scope of this standard.
Gear design is beyond the scope of this part of ISO An unfortunate effect of RC electrical filtering is a phase shifting of data that can influence analysis of test results.
This standard provides tolerances for unassembled gears only. Annex material provides guidance on filtering and information on comparison of gear inspection methods. The system of classifying very accurate gears with a low number, instead of retaining the method of AGMA Columbia Gear Corporation W. Definitions and allowable values of deviations relevant to flanks of gear teeth. No particular method of measurement or documentation is considered mandatory unless specifically agreed upon between manufacturer and purchaser.
When properly applied, gears manufactured by specific control techniques will be found to be of uniform accuracy.
Accuracy grade numbers are reversed—A smaller grade number represents a smaller tolerance value and, as such, a higher quality gear. This clause presents considerations for control of the 20155-1-a01 phases of manufacturing, including the recommended methods of measurement control.
Fis fis cp Size: Profile inspection includes total deviation, Fa, form deviation, ffa, and slope deviation, fHa. In some cases, measurement instruments follow the minimum requirements by default. It is important to understand that various gear measuring instruments use different testing procedures, some measuring 2015–1-a01 the normal direction, some measuring in other directions.
The committee agreed that a new gear classification system was needed: This should also include a determination of the uncertainty of the measuring process.
A filter that excludes the shortest and longest wavelengths highest and lowest frequencies of variations, thereby leaving only medium wavelength medium frequency data, is called a bandpass filter.
A New Standard in Gear Inspection
One type emulates the characteristics of electrical filters with or without the phase shifting characteristic of RC circuits. This includes, at one extreme, those of long duration, such as a general concavity. Suggestions for improvement of this standard will be welcome. 2015-1a01 or manufacturing a special master gear must be scheduled to be available when the manufactured gear is to be inspected by composite measurements.
For undated references, the latest edition of the referenced document including any amendments applies.
ANSI AGMA A01_百度文库
If improved performance is desired, modifications of material, heat treatment, and accuracy level should be considered. In this standard, lower AGMA accuracy grades designate higher precision in order to be consistent 201-51-a01 international standards.
When applications warrant, detailed specific measurements, data analysis, and additional considerations may be necessary to establish acceptance criteria for a gear.